System Set-Up - Model 3DAA
|
Click to View Detail
|
The original 3D Active Ambient system, Model 3DAA, is designed to work alongside a conventional wireless in-ear (IEM) system. The system is available in two models:
- 3DAA-1 (with Model 3D-1 single-driver ambient earphones)
3DAA-2 (with Model 3D-2 dual-driver ambient earphones)
The system components are:
- 3D-M bodypack mixer (1/8-inch stereo input)
- 3D Ambient Earphones (custom-fit, single or dual driver)
- Jumper cable (1-foot, 1/8-inch stereo connector plugs)
|
Click to View Detail
|
To set up your system, you will need a fresh 9V alkaline battery and a working sound source, preferably your wireless IEM receiver. Any other device with a 1/8-inch stereo output (such as a portable CD player or MP3 player) will also suffice. Please refer to the photos indicating the various controls and features of the 3D-M bodypack mixer. (NOTE: Your system was shipped with a fresh battery installed and the earphones connected.)
- Using the latch located above the Sensaphonics logo, open the 3D-M bodypack mixer and insert a fresh (K) 9V alkaline battery. Note: The battery only fits one way: negative terminal up, positive terminal down.
- Cable connections - Plug one end of the supplied short black jumper cable into the (D) IEM Input jack of the 3D-M mixer (a single 1/8-in. input jack found on the left side panel). Plug the other end into the output jack of your IEM receiver (where conventional earphones would plug in). We recommend looping the jumper cable through the (G) strain relief slot beneath the input jack (see photo).
- Plug your 3D Earphones into the (F) dual input mini-jacks located on the right side panel of the 3D-M. Prior to plugging in, loop the cable through the (G) strain relief slot located beneath the jacks.
- Using the recessed (A) on/off switch on top of the 3D-M, turn on the power. The green power status LED beside the switch will light. Your 3D Active Ambient system is now active.
- Insert the 3D Earphones in your ears (see Inserting Earphones section). Make sure you achieve a full seal for good isolation and extended bass response.
- Toggle the (C) Mode switch (on top panel of 3D-M bodypack mixer) to the "Full Ambient" position, so it points toward the outer edge of the pack. You should now hear the sounds around you (stage ambience) normally, just as if you were not wearing any earphones.
-
Now flip the (C) Mode switch to its other position, "Perform." (The switch should now point toward the indicator lights.) You should now hear the ambient sound at a reduced level, depending on the setting of the internal Ambient Background rotary switch (see Operating Modes - Perform Mode).
-
Next, add sound from your IEM system (or portable audio player). Use the volume control on your IEM bodypack (or other source) to adjust the volume of your monitor mix.
-
Staying in Perform Mode, adjust the amount of ambient sound added to the IEM mix. Open the (E) battery compartment and locate the (X) rotary Background Ambience control (above the battery). Using this 8-position switch, add the desired level of ambient sound to the IEM mix. We recommend doing this during sound check. Once you are satisfied with this mix, you're ready to play.
Remember:
- In Perform Mode, the volume level of the direct monitor mix is controlled from your IEM bodypack receiver (or portable 1/8" device)
- The ambience level for Perform Mode is set with the rotary Background Ambience control inside the 3D-M bodypack mixer.
- In Full Ambient mode, the ambience level is always "full" (unity gain), just as if you were not wearing earphones.
3D Active Ambient Page Links
3D Main Page
3D Ambient Earphones
3D Bodypack Mixers
System Set-up (3DHW)
Operating Modes
Internal Controls
Indicator Lights
Inserting Earphones
Tech Notes
Technical Specifications
3D User Guide PDF (456 KB)
Helpful Links
How To Order
Audiologist Referral
Hearing Conservation info
Sensaphonics Audio Seal Test
Got questions? Ask The Sound Guy!
|
